Replacement Locks For Patio Doors at Lowe's
Replacing your patio door lock can be an easy method to increase your home's security. However, proper installation and routine maintenance is essential.
It is essential to know what kind of patio door lock you are using in order to replace it successfully. You can identify the type by observing the size of the screw hole as well as end face plate type.
Identifying the lock you have
If you are considering purchasing a new lock hardware, it's essential that you be aware of the differences between kinds of locks. This will assist you in find the best replacement, making sure that your home is safe and secure.
The most common type of lock is the cylinder lock, also known as pin and tumbler locks. This lock type makes use of the top pins, bottom pins, and springs to keep the key hole and plug secured. Cylinder locks come in a variety of sizes and it is essential to know the exact length and diameter of the cylinder you currently have before purchasing a replacement.
To determine the size of your lock, use a screwdriver to loosen the screws holding the cylinder in place, and then carefully pull it out. Then, take a measurement in millimeters that lies between the outer edge and the inside of the cylinder. You can then compare this measurement with the measurements of the new lock you're planning to buy. This will ensure that the new lock is the correct size and will fit in the existing door lock hole.
Keys can also be used to test the dimensions of a lock that is already in use. If the key easily slides into the cylinder, it's the same width as the rekey kit that you need. If the key is unable to slide into the cylinder your cylinder is likely to have a different keyway, and therefore cannot be rekeyed so that it accepts the key of that brand.
It is best to always review the instruction manuals provided by the manufacturer that come with a kit for rekeying. Each type of lock comes with its own set of specific installation requirements. It is recommended to take the time to thoroughly test the new lock after you have installed it to make sure that it works well and gives you the highest level of security. It is also important to be aware of any additional features of your new lock, since they can affect its ease of use.
Measure the Width
A faulty patio door lock could lead to serious security concerns. It is essential to check your locks frequently and replace them when necessary. This will ensure that they are working properly and secure. It may also help to prevent problems such as a damaged latch or keyway. If your locks are worn or damaged, you can get replacements at Lowe's that will provide the security you need for your home.
Before you can purchase a new patio door lock, it's important to determine the dimensions of your existing one. This will help you determine the size of lock you should purchase and reduce the possibility of purchasing an unsuitable lock. fit. You'll need two measurements to accomplish this that are the backset and the depth of the case. The former refers to the distance between the edge of the lock's face to where the centre of the round hole that the spindle of the handle passes through, while the latter refers to the depth of the body of the lock which can be seen from the outside of the door.
When choosing the type of lock you want to use it is essential to think about how you'll be using your doors. For instance, if your sliding doors open horizontally, you'll have to choose a top and bottom tab style lock that engages with the strike plate, preventing the door from being pushed or lifted open. If your patio doors open vertically, you'll have to select a mortise latch with a spring loaded hook latch to provide additional security.
When determining the dimensions of the lock you have it is important to note the location of the screw holes. Certain mortise locks feature round screws, while others use square screws. You'll be able to determine where the keyway is located. Some locks have a vertical keyway, while others have a 45-degree angle. Take a photo of the lock using a digital camera to make sure you get the proper replacement.
After you've measured now is the time to start shopping for your new patio door lock. On the internet, you can find a wide range of top-quality locks. Many of the brands have advanced security features that will protect your home. It's important to look at locks and read reviews before you purchase. Don't forget to maintain your locks regularly to avoid dirt and debris interfering with your doors.
Make sure you check the screw holes
Patio doors are an important aspect of the security of your home. They must be inspected for signs of wear and tear to ensure they function correctly. Over time, the locks and spindle connecting the handles on the exterior and interior will need to be replaced. A sturdy lock will not only prevent unwanted entry, but it will also improve energy efficiency, security and security.
There are a variety of ways to narrow your search for a new lock if you don't have the right type. First, you must identify the type of keyway it uses. Aluminum patio doors are often equipped with a mortise locks with a rectangular cutout, while E2126 or E2079 locks are installed inside a recess in the frame. Uploading a photograph of the lock using your digital camera can help identify the type of lock it is.
You can also determine the type of lock by examining the screw holes. The majority of sliding patio door locks have screw holes that align with the latch keeper mounted on the side jamb. However, they are not always identical. Some screws might be longer than others, or have a different threaded finish. Some screws have washers or a hexagonal nut attached to them, which alter how they fit into the lock's hasp.
Once you have a good idea what kind of lock you have, you can start preparing to install the new one. First, you'll want to clean the lock using a soft cloth or brush to remove any dirt or debris that might be impeding its operation. Once clean, you can apply a silicone-based lubricant to keep the locking mechanism smooth and quiet.
It's a great idea to replace your screws with more long screws. This will allow you get a better grip, and also install the lock with less effort. Once Repair My Windows And Doors 've done that it's a good idea to check the handle to see how the latch hasp is engaged within the lock.
If it doesn't engage easily it could be necessary to put an hex nut or washer behind the hasp to get it to catch more of the door's lip. You can also put a shim on the side of the lockkeeper's jamb and see if it helps.
Check the Lock Snib
The snib acts as the mechanism for locking that is located inside your door handle. The snib is able to be disengaged and engaged to open or close your patio doors and is the first thing you need to look at if your locks aren't functioning properly. You should also check the keepers (located on the top and bottom of the door frame) for any looseness or misalignment that could cause them to shred. Make sure that your snib lock is correctly seated and that the lock has not been blocked or stuck in any other way.
The most commonly used patio door locks are mortise locks made of steel that protect sliding glass doors. They are inserted into the frame of the door and are available in a variety of styles which makes them a great security measure. Some are designed to hold keys, while some use an oval-shaped cutout for simple locking and unlocking.
Another option is a step-on lock with a thumb screw that secures your sliding doors in place, without requiring you to turn the knob or use the key. These locks are typically found on older metal-framed patio doors, but they can be a good choice to secure wood or vinyl-framed sliding doors too.
When you examine your existing patio lock, note the type and size of screw holes used to attach the escutcheon and the lock body. This will allow you to choose a lock that has the appropriate screw holes. It's an excellent idea to check your strike plate to ensure that it's aligned with the lock body and properly secured.
If you have Jason Windows boltlock sliding doors between 2000 and 2009, ensure the keeper screws are secured and not missing or loose. The screws keep the snib partially open in "vent" mode, allowing airflow, while still encouraging security. They are also essential to avoid your lock being cut. It is also a good idea for all locks to be inspected regularly and cleaned often to prevent debris, dirt or corrosion from hindering the operation of the lock.
If your snib has broken it is possible to replace the entire strikeplate and snib. If your snib just needs to be aligned it can be corrected by removing the strikeplate with an abrasive blade and then backing off the adjustment screws (located between the screw). Then, you'll need to move the strikeplate up or down until the engagement tongue lines up the Milgard logo.